Can you venetian plaster over wallpaper

It wasn't adhered well to the paper so it popped off in bigger pieces but it was still a bit of work. Pre-mixed drywall mud sets by drying out. If you wet it again it will soften up and come off AKA 'wet sanding'. If the surfaces are drywall it is likely to be just as fast to remove the wall and replace it with new.

Indem Sie weiterhin auf der Website surfen bzw. Mehr erfahren. Bathroom Fixtures. Dining Furniture. Sign In. Join as a Pro. Houzz TV. Houzz Research. Shop Featured Holiday Categories. Home Decor. Holiday Decor. Christmas Trees.

Holiday Lighting. Gift Cards. The Old House. Plastered over wallpaper! Email Save Comment 7. Sort by: Oldest. Newest Oldest. Like Save. Any advice on how to go about taking it down?

Related Discussions Need help on front entry way walls. Quick and dirty with the photo you gave - bring home these swatches and see how they look against the wallpaper and floor. For wainscot - bm hushed hue.

For core wall where stripe is now try bm elmira white. If you bring home the little paper swatches and put them on the rail or against the floor, your eye will tell you if I've guessed close enough.. You can go deeper on the core wall in the neutrals if you desire, but echoing wainscot tone but a tad deeper will help the eye since you now have a pattern on the floor as well as the upper wall.

If the paint on your wall is in good condition, then a professional will likely be able to start the plastering process straight away. In reply to Frank4short: Yes traces of paste will not affect the plaster, but bits of wallpaper will — but yes tricky bits do tend to come off when the plaster is applied. The cost of plastering a room depends on the size of the room, as mentioned above.

Before you learn how to skim coat your walls, you need to first prepare the wall. The best way to do this is to use a primer to quickly seal the wall from further damage. Part of the reason you skim coat is to give the whole wall a nice, even finish. There are two types of joint compound that can be used for skim coating: setting-type joint compound and ready-mixed joint compound.

Setting compound is a powder that sets to a very hard finish when mixed with water, similar to the way concrete sets. Scrape any loose paint, scrim any air line cracks, give the walls two coats of PVA, when dried apply two coats plaster. All paint should be removed and sanded down fully before skimming. If glue remains, use Universal Oil Base like Kilz or a shellac primer, latex will soften and raise the remaining adhesive.

Be especially careful to seal any remaining backing paper, or it might lift later, pulling the paint up with it. This is another good reason to remove all remaining backing paper before priming.

I have had some walls plastered and used pva glue as a sealant to paint over. This works fine. Soak them in a bucket to saturate them, and use hot water. Actually, I initially sanded with traditional sandpaper but found that the grit gummed it very quickly.

Then I tried steel wool, but it left tiny metal shards behind that changed the color of the wall. You can see how shiny and deep the color gets after sanding. My manufacturers instructions also recommended burnishing after sanding. I tried this but found no change in the look of the walls, so I decided that the sanding was sufficient. Here is our partially-finished den after venetian plastering all of the walls.

I have been asked why I picked this particular color venetian plaster. Frankly, I wanted something very bright and happy. I found it on 15 spot, you should build quality backlinks , it will help you to rank to google top I know how to help you, just type in google — k2 seo tips.

You are commenting using your WordPress. You are commenting using your Google account. You are commenting using your Twitter account. You are commenting using your Facebook account. Notify me of new comments via email.

Notify me of new posts via email. Skip to content. We bought our house for a pretty good deal because it initially looked like this: The faux paneling was in really good shape…. I did some experiments and found that without proper primer, my venetian plaster over wallpaper would develop one of the following: -tiny bubbles….

Share this: Twitter Facebook. Like this: Like Loading Bookmark the permalink.